functionalprint

Design by @canthidium

SkyWatcher Star Adventurer is my grab and go kit for astronomy and I take it with me abroad too. I dont want to carry around steel counterweight when Im abroad, especially air travel with them can be costly. So I came up with this solution that holds two 0.5l cans to use as counterweight. On the V2 Ive also included screws and...

Various knobs for cylinder head screws with M3/M4/M6 or M8 thread. For explanation, I have designed two different versions. The standard version has a hexagon socket integrated in the knob. The screw is inserted or glued onto this, whereby the thread length of the screw remains the same. The "thread" - version is for high stress...

Simple hooks on bracket designed to fit on VW T5. may fit other VWs can be printed on FDM or resin (I would advise a thicker wall with good drainage if resin, a solid print will not endure well)

Swapping out a broken intake manifold and needed to replace my throttle body gasket. Printed in orange TPU because that’s what I had on hand.

Paint mixer model 2 The hole is 8mm with tolerance already applied. If you are interested in supporting my work and possibly having access to the original STEP file of this model, you can receive it with a small donation. The donation is voluntary, but any contribution is appreciated. Thank you for your support!

My most complex model to date, can be configured with as many tasks as you want.

Years ago when I was building this CNC machine, I decided to design and print a NEMA23 stepper motor cover to wire the machine neatly. Today, I upgraded the stepper to an servo. All I took was a screwdriver....

Door mounted container for sauce/gravy packets. Approx. 1.5in deep. Use a single 5lbs capacity command strip to mount.

I’ve created this nozzle insert for the Prusa Toolbox, it’s for the standard Prusa MINI nozzles which should be the same dimensions as E3D V6.

I’m in the process of building this - should be done within a week if my needles will come in. Really looking forward to it since I started hand knitting a pair of socks ~4 years ago and they’re maybe 20% done :D...

This is a spoon that allows fast and precise spooning. You can easily fill your smallest and largest dessicant containers without spilling the tiny pearls - say goodbye to funnels. The unscaled spoon can hold ~12ml that is 10g of silica-gel pearls. Simple print, no supports, three walls, can be scaled if needed

My phone with the case is just barely too big for the slot in the K480, so after a few years of saying I should do something about it I finally did! Designed in Onshape, printed on a modified CR-10v2. Would welcome any suggestions, I already have v3 ready to go to fix the slot bit, it’s just a titch too big.

This is an upgrade for the "Parkside Multi Grinder Holder" by rechena. Please also check the source creator. The changes are the following: The lower rear part has been reduced in height. The front part has been reduced in height, different for Parkside and Dremel. These changes were made to ensure the horizontality of the tool....

Exact same file as the one posted by HarderDIY just with the model rotated so it prints on end. Find it easier to remove the supports that way. I printed at 0.75 scale for a more reasonable size for a keychain. I may re-upload this with the prongs on the male end separated a touch as it has a bit more play than I would like when...

printables.com/…/389110-under-desk-mount-for-appl…...

Heyho I wanted to mix a few samples with different colours or additives with epoxy resin and was looking for small mixing sticks. Unfortunately I haven't found anything really suitable in size. So I constructed a mixing stick myself. It was so small that it could just be made cleanly with my 0.6 mm nozzle. XS = 24,5 mm Diameter...

I added a hole to be able to release the clip after it clicked. No other changes to it. The original part: https://www.thingiverse.com/thing:2594163 The idea for the hole: https://www.thingiverse.com/thing:5364218

Hi guys! Here is my engine cover design for the well beloved Simson S51 Moped. It features a removable ignition cover, so you can replace it any time with the open one or with anything you like. It also features a regular clutch bowden adjuster/tensioner. I hope you will like this one! Other designs are coming soon. #LP...

4 original latches were broken, I tried to make them from different ones - with a larger wall thickness when printing, with a large infill, from PETG and SBS plastics. All broke down over time. I made a spring latch, there is nothing to break in it. need: 4ps screw M4 25 mm - for model Celling mount 2ps screw M4 25 mm, 4ps M4 12...

Is there a way I can track how much filament is left on a roll?...

My kids broke the flap on one of our sockets, so I had to look into getting them replaced....

Inspired by the "CNC 3018 Pro - Dust Collector" I designed this suction adapter, because I wanted to forfeit as little freedom of movement laterally as possible and the motor diameter did not fit. Additionally, I like the idea with the brushes from the Heise-Make suggestion. The lower shell is removable to change the drills and...

Boite de type container permettant le rangement des outils de l’imprimante Creality K1, il semblerait que cela ne puisse convenir à la K1 Max. La boite, haut et bas sont en PLA ainsi que le clip. Le reste est en TPU. Les différents axes de la boite sont réalisés directement avec du filament PLA. L’ attache clip, en TPU...