Nobody's mentioned lighter fluid so far, but that stuff works well. Dad always used Ronsonol and it's quite cheap. It's also highly flammable, so mind that.
The lighter fluid that the parent poster is talking about, Ronsonol, is not the stuff that goes in butane lighters, nor is it the "lighter fluid" used to start charcoal barbecues. He's talking about the stuff that goes into Zippo and similar refillable lighters, stuff that's also called "naphtha".
If you want to use it as a solvent with much frequency, you can get the stuff at dramatically-lower unit prices in much larger containers than what Ronsonol is sold at.
Keep in mind that this is potent stuff and can damage some surfaces. For example, another user is talking about using Goo Gone above to remove adhesive from paint on a wall. Naphtha is more-or-less paint thinner -- your wall's paint will dissolve in it. It'd be fine on glass, what OP is intending it for, but if you use it elsewhere, be careful with it, try it on a small amount of the surface somewhere first to see if it damages it.
It can also cause skin irritation. Probably not a big deal unless you're regularly using it, but worth keeping in mind.
I also have a container of white spirits, which are similar but less volatile.
I don't smoke, but I absolutely adore the sound that a Zippo makes when flicked open and struck, and wanted to get one a while back. I was kind of appalled at the fluid pricing -- the Zippo-brand fluid is even pricier, and I've seen the Ronsonol fluid itself recommended as a lower-priced alternative.
There are a lot of other things that people can burn in the refillable lighters, but I went through various testing that other people did and tried some myself, and none other than naphtha are really satisfactory. Some -- like white spirits -- aren't volatile enough, and won't maintain a consistent flame. Some, like gasoline, or low-water-content isopropyl alcohol, are too volatile and evaporate even more quickly than the regular fluid does or risk making an out-of-control fire.
Also works for the hand-warmers, which use the same fuel (and go through a great deal more of it than the lighters, so it's more-important there).
On an side note, I really wish that lighters of that sort would introduce some type of gasket that isn't dissolved by the fuel to help reduce the fuel vapor leaking out of the device when closed, or maybe some sort of other mechanism that seals the fuel reservoir off when the lighters are closed. As it stands, for a regular smoker, the fuel loss isn't a huge deal, but for someone who infrequently uses a lighter of the sort, the fuel loss is much more obnoxious -- it only takes several weeks for the reservoir to empty itself, in my experience.
Alcohol solvent can make this worse depending on the adhesive. It can just spread the stuff and thin it out. Someone else suggested oil, that's the ticket. Bit of olive oil on a rough cloth brings it right up. Wd40 was also suggested, same idea. You want it to move easily, not dissolve.
WD40 is great for dealing with things that are rusted in place, which is what it's supposed to be used for. It's just that it's not a great lubricating oil, and people often recommend it for use as that. Too thin and leaves a waxy residue to repel more water from rusting the surface, which you often don't want in things that you're lubricating.
Time - Federation takes time. Especially if servers are overloaded or haven’t allocated enough federation workers. Both of these things have been true at some point for most instances since the population boom.
Defederation - Different instances can defederate from other different instances. So say for example I have three instances, lemmy.one, lem.two, and kbin.three. In this example, lemmy.one has defederated from kbin.three and the post in question is on lem.two/c/community.
You now have three scenarios:
A user visits lem.two/c/community and sees all the content.
A user visits kbin.three/m/[email protected] (or however kbin does cross instance URIs, I’m not familiar). This user sees most of the content. The limited factor here being time.
A user visits lemmy.one/c/[email protected]. This user sees most of the content, but no comments from kbin.three because of defederation.
And I could be wrong, but I believe vote federation is separate from comment federation, so if that takes more time, then the comments sections might look different even if they have the exact same comments because of vote sorting.
Time - Federation takes time. Especially if servers are overloaded or haven’t allocated enough federation workers. Both of these things have been true at some point for most instances since the population boom.
Is this why I often don't see reply notifications?
I strongly recommend deepl.com It’s by far the best among the ones I tried. It can translate using the appropriate wording for the context and it also has a section (deepl write, accessible from the topbar) where you can past your english texts and get better wording.
Also the free plan covers most use cases. If you need the pro it’s worth it imo
AskKbin
Top
This magazine is from a federated server and may be incomplete. Browse more on the original instance.