3D-printed EDC (3d-cnc.de)
Pen holder with an integrated ruler and USB-stick storage in the top cap....
Finally finished my first RC car (lemmy.world)
I finally finished model 7 (Buggy) from 3dsets. It was fun to build, but mistake to take it in forest (one screw loose near one rear wheel).
E-Lock is finished. (lemmy.world)
This is a lock designed link your device to a fixed point (A lock)....
Prusa MINI FW-5.1.0a input shaping first print. (15min benchy; Actively adding notes as I test.) (lemmy.ca)
Prusa dun good with this surprise update....
I printed and painted a Gonk Droid from StarWars (discuss.tchncs.de)
I needed a presence sensor for my home office, so I took a Gonk Droid model from Printables, hollowed it out using negative modifiers in PrusaSlicer and then spent waaaay too long painting and grunging it up I also manually wrapped wires around the legs to give it a bit more visual interest. Inside is a Pico W, a mmWave sensor...
Host 3D parts? [Printables won] (lemmy.world)
Printables won. I will upload my files and link them here. I shouldn’t create another post since nobody likes spam. (sigh… What am I doing with my life?)...
It was not a loose thermistor after all, thank you for your help! (media.kbin.social)
One of my favorite 3D printed organizations. Custom silverware drawer (i.imgur.com)
cross-posted from: lemmy.world/post/5265624...
My paint storage setup for painting 3D printed models. (lemmy.world)
cross-posted from: lemmy.world/post/5201933
Screw storage for 3D prints. Still need to extend for more stuff. (lemmy.world)
cross-posted from: lemmy.world/post/5201970
Finally organized all my kitchen containers. Bonus custom spice rack. (lemmy.world)
Finally got around to printing a bunch of lid holders and got everything nice and neat. Some missing because they are in use. Also you can see my printed spice rack.
First print with PETG (lemmy.eyeofthestorm.place)
I’ve heard (and seem) many a horror story about PETG and was ready for hours of troubleshooting. Generic PETG settings in Prusaslicer and honestly this print couldn’t be much better! There’s a few layer inconsistencies, but those should be pretty trivial to fix after I get a temp tower done....
Uh, is this a loose thermistor? (media.kbin.social)
Clean finish while ironing (lemmy.world)
I’ve been tuning to print at a 0.1mm layer height, the ironing turned out like this. The left side of the Z is a little textured and more shiny....
PAROL6 Desktop Robot Arm GPL-V3 with simulator/software/useful precision/low cost (raw.githubusercontent.com)
github.com/PCrnjak/PAROL6-Desktop-robot-armwww.youtube.com/watch?v=PiBCbHtvbpEpiped.video/watch?v=PiBCbHtvbpE...
Melting 3D Printed eReader cases on my deck. (programming.dev)
I made a 3d printable eReader case for my wife. Wanted to test what would happen if we water logged them and left them in the sun to dry....
Lovecraft (lemmy.eyeofthestorm.place)
Model by Fotis Mint. Took about 15 hours at 0.12mm layer height
Gyroid infil appreciation post (i.imgur.com)
I’ve been using gyroid infil almost exclusively since I first tried it....
Plate difference (lemmy.world)
Recently I started printing on Bambulab (previously on Průša Mini). If anyone is curious about how much difference is it
Need help setting up my filament runout sensor on my Voxelab Aquila running Alex firmware (i.imgur.com)
As title says. I got myself a filament runout sensor, wired it, designed and printed a holder for it and now I am experiencing some issues. I hope someone here can help me....
I'm not sure... (lemmy.world)
but I think it might be!
Pegboard PC (lemmy.world)
(Not cross-posted by OP)...
Be honest folks, how bad are y'all's resin build plates? (files.catbox.moe)
It still prints great, but damn is it not that pretty anymore...
WTF is ozzing around my thermistor and heater (reddthat.com)
I was printing a benchy on my monoprice select miniwitha a e3d v6 nockoff and I saw plastic ozzing around my hotend
I suppose this is why my hotend fan stopped working... (i.imgur.com)
Took a couple failed prints to figure out something was wrong. Pulled the filament and saw it was melted WAY too high! Thankfully I’ve got a pack of spares, so pretty simple to swap out.