functionalprint

This magazine is from a federated server and may be incomplete. Browse more on the original instance.

Meta Quest 3 Wall Mount by 10P6 (www.thingiverse.com)

This is a wall mount I designed and made for the Meta Quest 3 VR Headset; I also made a wall mounts for the Quest 1 and 2 when they were released, (see other designs) and was hoping to have this wall mount compatible with the Quest 1 and 2, but the design of the Quest 3 prohibits that. I have added three new STL files to make...

Latching Lock for Micro Servo SG90 9G by peaberry (www.thingiverse.com)

This is an automatically latching lock which is powered by a Micro Servo SG90 9G. This makes it easy and inexpensive to interface to most microcontrollers such as Arduino. It is designed to engage with a pin of 3mm to 4mm diameter (not part of this model). When the pin enters the slot, it causes the mechanism to latch. To unlock...

Large Machine Vise with Trapezoidal Thread by blecheimer (www.thingiverse.com)

I was just playing around with printable trapezoidal threads and before I realized it, I had designed a large machine vise… The vise has a clamping range of 120x120mm. It is good for circuit boards because plastic is non-conductive. Standard trapezoidal threads (30° thread angle ) or ACME threads (29° thread angle) are very...

Electrical Tape Dispenser (Duck Brand 282289 Economy) by kdrummer (www.thingiverse.com)

This was remixed from UncleFrankSays version to hold a different brand of electrical tape which had a different inner diameter. If you read his comments on the serration, it's really only cosmetic as it doesn't function very well because electrical tape doesn't tear well. What is nice about this, however, is that it gives you a...

4 PIN LED Strip Light by MyCreationStation (www.thingiverse.com)

This is a variation of my 3 PIN LED Strip thing 6123191. This is for 12v 10mm LED strip lights. The height is 4mm so it doesn't add height to the height of my pictured IP65 strip. Yes, it's not soldered but you can see the wires fit. 9/20/2023 Update: Added info that this is a Remix of https://www.thingiverse.com/thing:5223739

Star Adventurer travel counterweight kit by UniqueMushroom (www.thingiverse.com)

SkyWatcher Star Adventurer is my grab and go kit for astronomy and I take it with me abroad too. I dont want to carry around steel counterweight when Im abroad, especially air travel with them can be costly. So I came up with this solution that holds two 0.5l cans to use as counterweight. On the V2 Ive also included screws and...

Dremel/Parkside Multi Grinder Holder by erevan12 (www.thingiverse.com)

This is an upgrade for the "Parkside Multi Grinder Holder" by rechena. Please also check the source creator. The changes are the following: The lower rear part has been reduced in height. The front part has been reduced in height, different for Parkside and Dremel. These changes were made to ensure the horizontality of the tool....

Key Ring Buckle - On End by MakerIke (www.thingiverse.com)

Exact same file as the one posted by HarderDIY just with the model rotated so it prints on end. Find it easier to remove the supports that way. I printed at 0.75 scale for a more reasonable size for a keychain. I may re-upload this with the prongs on the male end separated a touch as it has a bit more play than I would like when...

Stirring rod mixer for paint & epoxy support free (fully printable & wood) by MeisterEdel (www.thingiverse.com)

Heyho I wanted to mix a few samples with different colours or additives with epoxy resin and was looking for small mixing sticks. Unfortunately I haven't found anything really suitable in size. So I constructed a mixing stick myself. It was so small that it could just be made cleanly with my 0.6 mm nozzle. XS = 24,5 mm Diameter...

Simson S51 engine / ignition cover by Pogo_01 (www.thingiverse.com)

Hi guys! Here is my engine cover design for the well beloved Simson S51 Moped. It features a removable ignition cover, so you can replace it any time with the open one or with anything you like. It also features a regular clutch bowden adjuster/tensioner. I hope you will like this one! Other designs are coming soon. #LP...

Spring snap catch (does not break more) by KeyM (www.thingiverse.com)

4 original latches were broken, I tried to make them from different ones - with a larger wall thickness when printing, with a large infill, from PETG and SBS plastics. All broke down over time. I made a spring latch, there is nothing to break in it. need: 4ps screw M4 25 mm - for model Celling mount 2ps screw M4 25 mm, 4ps M4 12...

Creality K1 Rangement outils/Creality K1 Tool Storage by jpascal30 (www.thingiverse.com)

Boite de type container permettant le rangement des outils de l’imprimante Creality K1, il semblerait que cela ne puisse convenir à la K1 Max. La boite, haut et bas sont en PLA ainsi que le clip. Le reste est en TPU. Les différents axes de la boite sont réalisés directement avec du filament PLA. L’ attache clip, en TPU...

CNC3018 Pro Dust Deduction by DanielDo (www.thingiverse.com)

Inspired by the "CNC 3018 Pro - Dust Collector" I designed this suction adapter, because I wanted to forfeit as little freedom of movement laterally as possible and the motor diameter did not fit. Additionally, I like the idea with the brushes from the Heise-Make suggestion. The lower shell is removable to change the drills and...

Lens filter case customizable | Objektiv Filter Gehäuse anpassbar by tobbegraf (www.thingiverse.com)

Hi, this is a lens filter case. I made it for my variable nd filter. The diameter and height are customizable in the FreeCAD file (in the table "data"). The files here are with 66mm diameter and 12mm height. Hallo, Dies ist ein Gehäuse für Objektiv Filter. Ich habe es für meinen variablen ND Filter erstellt. Der Durchmesser...

Nemesis Boardgame: Fast Setup Organizer by ogre_ergo_sum (www.thingiverse.com)

This Nemesis organizer is designed for ease of setup and packing away. Top layer trays go to the table. Cards stay sorted in the organizers. Everything packs away into the original box. This incredible convenience comes at a cost. 1.4kg of PLA and 40 hours of printing on a Bambu @ 0.20 layer thickness. No support required.

  • All
  • Subscribed
  • Moderated
  • Favorites
  • random
  • uselessserver093
  • Food
  • aaaaaaacccccccce
  • [email protected]
  • test
  • CafeMeta
  • testmag
  • MUD
  • RhythmGameZone
  • RSS
  • dabs
  • Socialism
  • KbinCafe
  • TheResearchGuardian
  • Ask_kbincafe
  • oklahoma
  • feritale
  • SuperSentai
  • KamenRider
  • All magazines