Well I didn’t say it fixes the problem. I’m just saying you’re ignoring it. By ignoring the issue, you’re empowering the issue. Which is definitely worse than not doing anything. So your opinion is wrong and ill-educated.
Are you serious? Instead of doubling down on your ignorancy by asking rhetorical questions you could also try to inform yourself. The answer to your question is in OP’s post:
The children in these photos/videos can’t make pornography, they’re sexually abused into making this material. CP insinuates that it’s legitimate porn with children. CSAM, on the other hand, calls it what it is: sexual abuse of children.
I have printed some food safe prints for a friend couple of times now. Nozzle is stainless steel, Filament is natural HIPS. Stainless & HIPS are both food safe materials (if not mixed with color pigments). After the print, you need a clean surface. HIPS can be smoothed in an Acetone-Bath. Simply put it in for 10-15 min and you’ll have a glossy finish.
HIPS is very easy to print in an enclosure and the resulting product is fairly stiff and durable. It’s also temp resistant up to 90-100°C. So it’s dishwasher safe.
Do not inhale acetone vapor, wear respiratory masks that filter out voc like acetone vapor.
While being the cheapest, AC is also the type of heating with the least amount of comfort, while the most expensive solution, underfloor or wall heating is the best comfort. Radiant heat is much less intrusive than blowing air around violently.
I agree. One thing I’d like to add: There are also low thermal mass floor heating systems available nowadays (usually dry, built on top of a layer of Insulation). These aren’t that slow to react. But of course, these bring not only advantages but also drawbacks.
Wearing a gun may give you some protection, but it also brings you a false sense of security and introduces countless new risks while negleting the source of the issue. If you’re actually living somewhere, where it’s “normal” to wear guns it’s a far better idea to just relocate. But then, many folks are just scared and don’t actually gain any increased safety from wearing a gun.
I actually have Marlin + Octoprint but found out recently that Klipper exist. I read everywhere that Klipper is better but I don’t really get why. I understand that Klipper use raspberry as powerfull calculator instead of the STM32 of the printer, but octoprint is used to send Gcode to Marlin too… So what’s the really...
I was once at the exact same point where you are now. Marlin+octoprint really is good enough for most cases once you’re up and running.
I pulled the trigger for klipper a couple of years ago and honestly never looked back. Mainsail is just so much more refined and usable than octoprint. Tuning Firmware Settings in klipper is so much simpler than marlin, it’s just a breeze.
Combined with modern controller board (f.e. mks skipr), modern drivers like TMC2209, sensorless homing, Canbus-toolhead, resonance measuring, mmmh… chef’s kiss ;)
The Fairphone 5 is less about what comes in the box and more about what you get over the years (www.theverge.com)
My friend who runs the instance i am on nuked all the images cause some degen thought spreading cp was a good idea. So have some more motivational word art (lemmy.letthewookiee.win)
Help - 3D Printer for food manufacturing
Hi,...
TIL just 20% of European homes have air conditioning compared to 88% in US (www.nbcnews.com)
Tasers, taunts, torment: How 6 White officers subjected 2 Black men to hours of grueling violence, and then tried to cover it up (www.cnn.com)
Klipper vs Marlin
I actually have Marlin + Octoprint but found out recently that Klipper exist. I read everywhere that Klipper is better but I don’t really get why. I understand that Klipper use raspberry as powerfull calculator instead of the STM32 of the printer, but octoprint is used to send Gcode to Marlin too… So what’s the really...
Find the Culprit? (lemmy.world)
@mods: maybe link community !fixmyprint in the sidebar?